How to connect to internet (v0.1.0.4)

see also how-to-connect-to-internet-using-nokia-6120-classic-as-a-modem

1. Wireless Mobile Broadband Telkomsel Flash Unlimited Package
1.1. Using NetworkManager
1.2. Using wvdial

2. Wireless Mobile Broadband IM2 Broom Unlimited Package (UNTESTED YET)
2.1. Using NetworkManager
2.2. Using wvdial

3. Wireless Indosat Mentari/IM3 USIM Card
3.1. Using NetworkManager
3.2. Using wvdial

4. Wireless Indosat 3.5G Broadband Unlimited Package (UNTESTED YET)
4.1. Using NetworkManager
4.2. Using wvdial

5. Wireless XL Internet Unlimited Prepaid Package (UNTESTED YET) –reference : here
5.1. Using NetworkManager
5.2. Using wvdial

————————————————————————————–
You may use one of below internet dialer programs to make dial-up internet connection.
* NetworkManager
* system-config-network
* KPPP
* GNOME PPP
* wvdial

1. Wireless Mobile Broadband Telkomsel Flash Unlimited Package

—[unlimited package or volume based setting]—
APN = internet
Username = <blank>
Password  = <blank>
——- or ————
APN = telkomsel
Username = wap
Password = wap123

If you are a subscriber to unlimited package service then the setting as mentioned above.
The setting above also applies as volume based setting if you are a non-subscriber to unlimited package service.

—[Time base setting]—
APN = flash
Username = <blank>
Password  = <blank>

1.1. Using NetworkManager

step 1: Right click on network manager applet (located on the right side of GNOME panel)
step 2: Choose “Edit Connections …” (“Network Connections” window will appear)
step 3: Click “Mobile Broadband” tab
step 4: Click “Add” button and “Choose a Mobile Broadband Connection” dialog will pop up
step 5: Select the modem (in my case it is “Huawei Technologies E220 HSDPA Modem/E270 HSDPA/HSUPA Modem”)
and then click “OK” button
step 6: “Editing GSM connection 1″ dialog window will pop up.
Edit the “Connection name” so that it give you informative name and then fill in :

Number   = *99#
Username = <blank>
Password = <blank>
APN      = internet
Network  = <blank>
PIN      = <blank>
PUK      =<blank>

and then click “Apply” button. If the APN=telkomsel, then username=wap and password =wap123
step 7 : To make internet connection, Left click on network manager applet and select the connection name we have just created.

1.2. Using wvdial

step 1 : as root, edit /etc/wvdial.conf so that it will look like as follows:

[Dialer internet]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,”IP”,”internet”
Modem Type = USB Modem
ISDN = 0
Phone = *99#
Modem = /dev/ttyUSB0
Username = ”
Password = ”
Baud = 3600000

[Dialer telkomsel]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,”IP”,”telkomsel”
Modem Type = Analog Modem
ISDN = 0
Phone = *99#
Modem = /dev/ttyUSB0
Username = wap123
Password = wap
Baud = 3600000

step 2 : on the command line, execute below command:

su -c ‘wvdial internet’

OR

su -c ‘wvdial telkomsel’

When the internet connection has been established, you will see the values of Primary DNS and secondary DNS which will be required to do step 3.

step 3 : edit /etc/resolv.conf so that it will look like as follows (the values below are primary DNS and secondary DNS you obtain after executing step 2) :

nameserver 202.2.208.10
nameserver 202.3.210.10

Debian Experimental need not edit this file. It is automaticaly configured.

Note that NetworkManager will replace the contents of /etc/resolv.conf with its own version. So, you should always edit again /etc/resolv.conf if you want to run wvdial.

step 4 : now the internet connection is ready to use

2. Wireless Mobile Broadband IM2 Broom Unlimited Package (UNTESTED YET)

APN=indosatm2
username=<your userid, see the guide you get when you buy the prepaid card>
password=<your password, see the guide you get when you buy the prepaid card>

reference: here

2.1. Using NetworkManager

step 1: Right click on network manager applet (located on the right side of GNOME panel)
step 2: Choose “Edit Connections …” (“Network Connections” window will appear)
step 3: Click “Mobile Broadband” tab
step 4: Click “Add” button and “Choose a Mobile Broadband Connection” dialog will pop up
step 5: Select the modem (in my case it is “Huawei Technologies E220 HSDPA Modem/E270 HSDPA/HSUPA Modem”)
and then click “OK” button
step 6: “Editing GSM connection 1″ dialog window will pop up.
Edit the “Connection name” so that it give you informative name and then fill in :

Number   = *99#
Username = my-indosatm2-user-id
Password = my-indosatm2-password
APN      = indosatm2
Network  = <blank>
PIN      = <blank>
PUK      =<blank>

and then click “Apply” button.
step 7 : To make internet connection, Left click on network manager applet and select the connection name we have just created.

2.2. Using wvdial

step 1 : as root, edit /etc/wvdial.conf so that it will look like as follows:

[Dialer indosatm2]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,”IP”,”indosatm2″
Modem Type = USB Modem
ISDN = 0
Phone = *99#
Modem = /dev/ttyUSB0
Username = my-indosatm2-user-id
Password = my-indosatm2-password
Baud = 3600000

step 2 : on the command line, execute below command:

su -c ‘wvdial indosatm2′

When the internet connection has been established, you will see the values of Primary DNS and secondary DNS which will be required to do step 3.

step 3 : edit /etc/resolv.conf so that it will look like as follows (the values below are primary DNS and secondary DNS you obtain after executing step 2):

nameserver 202.2.208.10
nameserver 202.3.210.10

Debian Experimental need not edit this file. It is automaticaly configured.

Note that NetworkManager will replace the contents of /etc/resolv.conf with its own version. So, you should always edit again /etc/resolv.conf if you want to run wvdial.

step 4 : now the internet connection is ready to use

3. Wireless Indosat Mentari/IM3 USIM Card

—-Volume Base—-
APN=indosatgprs
username=indosat
password=indosat

—Duration Base—
APN=indosatgprs
username=indosat@durasi
password=indosat@durasi

reference : here

3.1. Using NetworkManager

Modify the configuration on section 1.1. based on data above

3.2. Using wvdial

step 1 : as root, edit /etc/wvdial.conf so that it will look like as follows:

[Dialer indosatvolume]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,”IP”,”indosatgprs”
Modem Type = USB Modem
ISDN = 0
Phone = *99#
Modem = /dev/ttyUSB0
Username = indosat
Password = indosat
Baud = 3600000

[Dialer indosatduration]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,”IP”,”indosatgprs”
Modem Type = USB Modem
ISDN = 0
Phone = *99#
Modem = /dev/ttyUSB0
Username = indosat@durasi
Password = indosat@durasi
Baud = 3600000

step 2 : on the command line, execute below command:

su -c ‘wvdial indosatvolume’
OR
su -c ‘wvdial indosatduration’

When the internet connection has been established, you will see the values of Primary DNS and secondary DNS which will be required to do step 3.

step 3 : edit /etc/resolv.conf so that it will look like as follows (the values below are primary DNS and secondary DNS you obtain after executing step 2):

nameserver 202.2.208.10
nameserver 202.3.210.10

Debian Experimental need not edit this file. It is automaticaly configured.

Note that NetworkManager will replace the contents of /etc/resolv.conf with its own version. So, you should always edit again /etc/resolv.conf if you want to run wvdial.

step 4 : now the internet connection is ready to use

4. Wireless Indosat 3.5G Broadband Unlimited Package (UNTESTED YET)

APN=indosat3g
username=indosat
password=indosat

4.1. Using NetworkManager

Modify the configuration on section 1.1. based on data above

4.2. Using wvdial

step 1 : as root, edit /etc/wvdial.conf so that it will look like as follows:

[Dialer indosatunlimited]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,”IP”,”indosat3g”
Modem Type = USB Modem
ISDN = 0
Phone = *99#
Modem = /dev/ttyUSB0
Username = indosat
Password = indosat
Baud = 3600000

step 2 : on the command line, execute below command:

su -c ‘wvdial indosatunlimited’

When the internet connection has been established, you will see the values of Primary DNS and secondary DNS which will be required to do step 3.

step 3 : edit /etc/resolv.conf so that it will look like as follows (the values below are primary DNS and secondary DNS you obtain after executing step 2):

nameserver 202.2.208.10
nameserver 202.3.210.10

Debian Experimental need not edit this file. It is automaticaly configured.

Note that NetworkManager will replace the contents of /etc/resolv.conf with its own version. So, you should always edit again /etc/resolv.conf if you want to run wvdial.

step 4 : now the internet connection is ready to use

5. Wireless XL Internet Unlimited Prepaid Package (UNTESTED YET) –reference : this link

APN=www.xlgprs.net
username=xlgprs
password=proxl

reference: here

5.1. Using NetworkManager

Modify the configuration on section 1.1. based on data above

5.2. Using wvdial

step 1 : as root, edit /etc/wvdial.conf so that it will look like as follows:

[Dialer xlunlimited]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,”IP”,”www.xlgprs.net”
Modem Type = USB Modem
ISDN = 0
Phone = *99#
Modem = /dev/ttyUSB0
Username = xlgprs
Password = proxl
Baud = 3600000

step 2 : on the command line, execute below command:

su -c ‘wvdial xlunlimited’

When the internet connection has been established, you will see the values of Primary DNS and secondary DNS which will be required to do step 3.

step 3 : edit /etc/resolv.conf so that it will look like as follows (the values below are primary DNS and secondary DNS you obtain after executing step 2):

nameserver 202.2.208.10
nameserver 202.3.210.10

Debian Experimental need not edit this file. It is automaticaly configured.

Note that NetworkManager will replace the contents of /etc/resolv.conf with its own version. So, you should always edit again /etc/resolv.conf if you want to run wvdial.

step 4 : now the internet connection is ready to use

---

Possibly related posts: (automatically generated)

• Share Your Internet Connection Wirelessly, Without a Router
• Feds Charge Cable Modem Modder With ‘Aiding Computer Intrusion’

~ by yunustj on December 8, 2008.